將輸入的電信號按比例地轉化成壓力輸出信號.
比例電磁鐵是帶中心螺紋和可更換線圈的濕式可控直流電磁鐵,
電磁鐵可通過外部電控器(3DREP型)和集成電控器(3DREPE型)精細控制
REXROTH比例閥的工作原理如下在不制動時,活塞在感載彈簧通過杠桿施加的推力F的作用下,處
于左端極限位置,這時閥門離開閥座打開,使輸入輸出油路相通。當開始制動時,來自助力器的壓力為P1的
制動液由進油口進入,并通過閥門從出油口輸至后制動管路.此時輸出液壓P,等于輸入液壓P1當制動踏板
力增大時,P1和P2同步增大。但由于活塞左側承壓面積大于右側,致使活塞左側受到的力也大于右側.
Rexroth比例閥的結構和其它參數一定的情況下,調節作用的初始控制壓力P·的值取決于感載的比例
閥感載彈簧預緊力的大小,其變化范圍在1.35～2.7MPa之I閏.因此只要使彈簧預緊力隨汽車實際軸荷的變化
而變化,就能實現感載調節。感載比例閥安裝在左后輪附近,其安裝方式使得軸荷增加時,感載彈簧被拉伸,折
點液壓PS增大;軸荷減小時.PS減小.這樣就使Ps隨載荷變化,實現了感載調節,使前后輪制動力分配更接近理想分
配特性曲線。
3DREP6C-14/25A24N9K4M
3DREP6C-20/25EG24N9K4/V
3DREP6C-14/25A24N9K4M，
DR30-5-5X/315Y，Rexroth
3DREP6CA-2X/45EG24N9K4/M
3DREPE6C-2X/25EG24K31/F1M-00
3DREPE6C-20/25EG24K31/AOM
3DREP6A-14/25A24N9K4M
3DREPE6C-20/25EG24N9K31/FLM-
3DREPE6C-2X/25EG24K31/AIM Rexroth
3DREP6C-13/25A24NZ4W
3DREP6C-11/Z5A 24NZ4M
3DREM16P-7X/200YG24K4V
3DREP6C-2X/25EG24N9K4/M
3DREP6C-2X/25EG24N9K4/M
3DREPE6C-20/25EG24N9K31/F1V=00
3DREP6C-12/25A24N9Z4MRRexroth
3DREP6C-12/25A24N924MR
3DREP6C-14/25A24N9Z 4M
3DREP6C-10R/25A24HZ4
3DREP6C-12/25A24NZ4M
3DREP6C-12/25A24NZ4M
3DREP6C-14/25A24N9K4M Rexroth
3DREP6C-11/25AG24NZ4M
3DREP6C-11/25AG24NZ4M
3DREP6C-2X/25EG24N9K4/M
3DREP6C-14/25A24K4M Rexroth
3DREP6C-20/25EG24N9K4/M00
3DREP6C-14/25A24NK4MZWR
3DREP6C-14/25A24NK4MZWR
3DREP6C-20=25EG24NPK/V=00
3DREP6C-11/25A 24NZ4M
3DREP6C-20/25EG24N9K4/MRexroth
3DREP6C-20-25EG24N9K4/M
3DREP6A-2X/45EG24N9K4
3DREPE6C-20=25EG24N9K31/FIM
3DREP6C-20=25EG24N9K4
3DREPE6C-20=25EG24N9K31/A1M=00;MNR:R900958788Rexroth3DREPE6A-20=25EG24N9K31/A1M=00;MNR:R901010402
3DREPE6C-20/25EG24N9K31/A1M
3DREP6C-20=25EG24N9K4/M=00 和主閥成套 Rexroth
3DREPE6C-2X/25EG24N9K31/A1M(R900955784)
3DREP6C-20/25EG24N9K4/M/00
3DREPE6C-2025EG24N9K31/A1M(R900955784)
3DREP6C-2X/25EG24N9K4/M Rexroth
